Sony FS100 and F3 Video Review

workshops-275 Sony FS100 and F3 Video Review

Sony FS100 and F3 compared from Ingenious TV on Vimeo.

The main aim of the shoot was to see how the FS100 held up against the F3. We shot on a bright sunny day by the River Thames and again in the evening in a typically lit living room. There were no big surprises. The FS100 is remarkably close to the F3. You would have no problems cutting between the two of them in a project.I did find that the FS100 LCD appeared less sharp and not quite as good as the F3’s even though they both use the same underlying panel. This is probably down to the additional layers required for touch screen operation on the FS100. I also did not like the 18-200mm f5.6 kit lens. There was too much lag in the focus and iris controls, but the beauty of this camera is that you can use a multitude of lenses. For the evening shoot I used a Nikon 50mm f1.8 which was so much nicer to use. On reviewing the footage I did find that we were tending to over expose the FS100 by half a stop to a stop, this does make making accurate comparisons difficult and I apologise for this. I believe this was down to the slightly different images we were seeing on the LCD’s. I did use the histograms on both cameras to try to ensure even exposure, but even so there is a difference. A small part of this is also likely down to the very slightly different contrast ranges of the two cameras.Oe thing we discovered, not mentioned in the video is that when you use a full frame lens, like the Nikon 50mm. You must ensure that the E-Mount adapter you use has an internal baffle or choke. If it doesn’t you will suffer from excessive flare. The adapter I had did not have a baffle and some shots (not used) were spoilt by flare. The adapter I have from MTF for the F3 has a baffle as do MTF’s E-Mount adapters, so these should not suffer from this issue.The FS100 performance is so very close to that of the F3’s (at 8 bit 4:2:0, 35Mb/s) that it is hard to tell the two apart. I believe the F3’s images are just a tiny bit richer, with about half a stop more dynamic range, in most cases it takes a direct side by side comparison to show up the differences.The range of camera settings and adjustments on the FS100 is not quite as extensive as on the F3, nor do the adjustments have such a broad range. However there is plenty of flexibility for most productions. If you don’t need 10 bit 4:2:2 then it is hard to justify the additional cost of the F3, both cameras really are very good. Despite some other reports else where I felt the build quality to be very good and the buttons, while small, are big enough and well placed. If you do want autofocus then you will be pleased to know that it actually works pretty well on the FS100 with only minimal hunting (of course you must use an AF compatible lens).I did also record the HDMI output to one of my NanoFlashes at 100Mb/s. Comparing these side by side it is extremely hard to see any difference. It is only when you start to heavily grade the material that the advantage of the higher bit rate Nanoflash material becomes apparent. There is less mosquito noise in the NanoFlash material. I was really impressed by the AVCHD material. The lack of noise in the images really helps. The FS100 really is the F3’s little brother. The pictures are remarkably close, which they should be as they share the same sensor. The FS100 packs down into a remarkably small size for transport. The loan camera from Sony was actually packed in a case designed for the MC1P mini-cam, about 15″x10″x5″ so very compact indeed. The F3 is considerably larger and bulkier, in part due to the extra space taken up by the built in ND filters.The lack of ND filters does need to be considered. There are some clever solutions in the pipelines from various manufacturers as well as existing solutions such as vari ND’s, screw on ND’s and a Matte Box with ND’s, so it’s not a deal breakerI think there is every chance that the FS100 will be the first NXCAM camera that I will purchase. It will be a good companion to my F3. It’s modular design will allow me to get shots that are not possible with the F3. I felt that the FS100 (with the 18-200mm lens that I don’t like) was better suited to “run and gun” than my F3 with either manual DSLR lenses or PL glass. You can, with the FS100 simply point the camera at your subject and hit the one push auto focus and auto iris and have an in-focus, correctly exposed shot. This is much more like a traditional small sensor camcorder in this respect. The long zoom range also makes this more like a conventional camcorder, although there is no servo for the zoom.
In conclusion, in my opinion, for “run and gun” or quick and dirty setups the FS100 with the 18-200mm lens has an edge over the F3 due to the fast auto focus and auto iris one-push controls. For more precise work and shallow DoF your going to want a different lens, something with manual control and calibrated focus and iris scales. For more demanding shoots then the F3 is probably the better choice with it’s slightly improved dynamic range and the ability to use S-Log and 4:4:4. In either case these cameras can produce highly cinematic pictures and I see no reason why you could not shoot a great looking feature with either.

4 thoughts on “Sony FS100 and F3 Video Review”

  1. Nice write up. I’m definitely considering this camera as my next large purchase. We do a lot of promotional work for non-profit organizations and currently use a Z5U (with Atomos HDD pulling from the HDMI out) and a D7000 as our main cameras, renting if we need to step up a bit. So one thing that interests me about the FS100 is it uses the same batteries as my Z5U and I can continue to use my Atomos system (which just happens to use the same batteries as well) to get QT ProRez footage.

    1. Yes you will be able to save some money using the same batteries and the Ninja with the FS100. That would be a nice lowish cost s35mm setup.

  2. Hi Alister,

    I have some suspicion that people can use the Sony FS100 for s3d shooting with the help of AJA and BlackMagic devices.
    Have you heard of anyone doing this?
    I remember Sony posting a video last year that this camera would be 3D ready.

    1. You can use a pair of FS100’s to shoot 3d but there is no way to sync the FS100 accurately so you will have temporal (time) errors, which translates to depth errors in your footage. You really need genlock to sync cameras for 3D. While you can use an external device to sync the camera outputs, this does not sync exactly when the cameras are taking the images, so your two un synced cameras could be capturing the left and right images at different moments in time and this can create all kinds of issues. If you have no option but to use FS100’s then you should use 60p as your temporal errors will be smaller than at 24p, but it’s still not ideal.

Leave a Reply

Your email address will not be published. Required fields are marked *

*

Camera setup, reviews, tutorials and information for pro camcorder users from Alister Chapman.

%d bloggers like this: