Just to clarify the differences between Detail settings and the Aperture setting.
Detail has a sub set of settings including: frequency, level, crispening, knee aperture, black and white limit. These sub settings all affect the amount and level of detail correction applied.
Aperture is a completely separate type of adjustment.
Detail works on contrast. The higher the contrast in an image, the sharper it appears. A bright sunny day will look sharper that a dull cloudy day because there is more contrast. detail works by increasing contrast by adding black or white edges to any parts of the image where the contrast changes rapidly, for example the edge of an object silhouetted against the sky. This increases contrast still further, making the image appear sharper. The crispening setting sets the contrast threshold at which detail gets added, level adjusts the amount.
Aperture is a simple high frequency boost. As fine details and textures are normally represented by high frequencies within the image, boosting high frequencies can help compensate for the natural fall off in lens and sensor performance at higher frequencies. This helps enhance textures and other subtle, fine details within the image look clearer.
Neither setting will increase the cameras resolution. Both make the image “appear” sharper. Detail correction IMHO is very un-natural looking and electronic, while careful use of aperture can help sharpen the image without necessarily looking un-natural.
After completing the multi camera shootout at Visual Impact, one thing was bothering me about the pictures from the PMW-350 and that was the way the specular highlights in the tin foil were artificially enhanced. During the test the camera was set to factory defaults, which IMHO are too sharp, but the foil in particular looked nasty. Since then I have been further refining my paint settings for the 350 and looking at detail and aperture. Today I was replicating the tin foil test and looking at the aperture settings (not the knee aperture) and I noticed that turning aperture on and off had a very pronounced effect on highlights but a much smaller effect elsewhere in the image. Normally I would expect the aperture setting to act as a high frequency boost making subtle textures more or less enhanced, which it does, but the amount of enhancement appears to vary with the brightness of the image with specular highlights getting a really big hit of correction. If you look at the images to the left at the top you have aperture correction on at +99. There are big ugly black lines around the highlights on the foil and the texture of the carpet has been enhanced. To some degree this is the expected behaviour although I am surprised by how thick the edges around the highlights are, this looks more like detail correction (it could be “ringing”). The middle images are aperture off, not zero but actually off and you can see that the edges on the foil have gone and the carpet is no longer enhanced. The bottom picture though with aperture on at -99 though is very interesting as the carpet appears slightly softer than OFF, which is not unexpected while the foils is sharper than OFF and this is not expected. I don’t like this behaviour I’m afraid to say as a typical way to get a filmic look from a video camera is to turn the detail correction off to give a natural picture and then use Aperture correction to boost high frequencies to retain a sharp image. On the PMW-350 you can’t do this as this as a high Aperture setting will give you those nasty edges on highlights. So what can you do? Well the 350?s native, un-enhanced resolution is very high anyway so it doesn’t need a lot of correction or boosting. The default Detail and Aperture settings will give some really nasty highlight edges so you need to back things off. If your going for a filmic look I would turn OFF aperture correction altogether, for video work with pictures that have some subtle enhancement I would use Aperture at around -20, certainly never higher than -15 unless you like black lines around specular highlights.
My current prefered detail, aimed at giving a very slight, not obvious enhancement are are as follows:
Detail Level -12, H-V Ratio +15, Crispening 0, Frequency +30, White Limit +30, Black Limit +40 (all other detail settings at default)
Aperture OFF for filmic look, Aperture -20 for video look.
I have also made some changes to the Matrix settings. I have been finding the pictures from Sony cameras to be a little on the Green/Yellow side so I have tweaked things a little to remove the yellow cast and put in a bit of red, this is a subtle change but really helps with skin tones, stopping on screen talent from looking ill! These settings work in the PMW-350, EX1/3 and PDW-700.
On an EX1/EX3 this works best with the Standard Matrix, On a PMW-350 or PDW-700 you can use it on it’s own or mix it with one of the preset matrices as a modifier. User Matrix On, R-G 0, R-B +5, G-R -6, G-B +8, B-R -15, B-G -9
Camera setup, reviews, tutorials and information for pro camcorder users from Alister Chapman.