Measuring resolution, Nyquist and MTF

The place to discuss general camera techniques and setups.
Post Reply
alisterchapman
Site Admin
Posts: 431
Joined: February 1st, 2011, 7:43 pm

Measuring resolution, Nyquist and MTF

Post by alisterchapman » March 10th, 2011, 9:50 pm

When measuring the resolution of a well designed video camera, you never want to see resolution that is significantly higher than HALF of the sensors resolution. Why is this? Why don’t I get 1920 x1080 resolution from an EX1, which we know has 1920 x1080 pixels, why is the measured resolution often around half what you would expect?
There should be an optical low pass filter in front of the sensor in a well designed video camera that prevents anything above approx half of the sensors native resolution getting to the sensor. This filter will not have an instantaneous cut off, instead attenuating fine detail at ever increasing amounts centered somewhere around the Nyquist limit for the sensor. The Nyquist limit is normally half of the pixel count with a 3 chip camera or somewhat less than this for a bayer sensor. As a result measured resolution gradually tails off somewhere around Nyquist or half of the expected sensor resolution, but why is this?
It is theoretically possible for a sensor to resolve an image at it’s full pixel resolution. If you could line up the black and white lines on a test chart perfectly with the pixels on a 1920 x 1080 sensor then you could resolve 1920 x 1080 lines. But what happens when those lines no longer line up absolutely perfectly with the pixels? lets imagine that each line is offset by exactly half a pixel, what would you see? Well each pixel would see half of the black line and half white line. So each pixel would see 50% white, 50% black and the output from that pixel would be mid grey. With the adjacent pixels all seeing the same thing they would all output mid grey. So by panning the image by half a pixel, instead of now seeing 1920×1080 black and white lines all we see is a totally grey frame. As you continued to shift the chart relative to the pixels, say by panning across it, it would flicker between pin sharp lines and grey. If the camera was not perfectly aligned with the chart some of the image would appear grey or different shades of grey depending on the exact pixel to chart alignment while other parts may show distinct black and white lines. This is aliasing and it’s not nice to look at and can in effect reduce the resolution of the final image to zero. So to counter this you deliberately reduce the system resolution (lens + sensor) to half the pixel resolution so that it is impossible for any one pixel to only see one object. By blurring the image across two pixels you ensure that aliasing wont occur. It should also be noted that the same thing can happen with a display or monitor, so trying to show a 1920×1080 image on a 1920×1080 monitor can have the same effect.
When I did my recent F3 resolution tests I used a term called the MTF or modulation transfer function, which is a measure of the contrast between adjacent pixels, so MTF 50 is where there is a 50% of maximum contrast difference between the black and white lines on the test chart.
When visually observing a resolution chart you can see where the lines on the chart can no longer be distinguished from one another, this is the resolution vanishing point and is typically somewhere around MTF15 to MTF5, ie. the contrast between the black and white lines becomes so low that you can no longer distinguish one from the other. But the problem with this is that as you are looking for the point where you can no longer see any difference, you are attempting to measure the invisible so it is prone to gross inaccuracies. In addition the contrast at MTF10 or the vanishing point between black and white will be very, very low, so in a real world image you would often struggle to ever see fine detail at MTF10 unless it was strong black and white edges.
So for resolution tests a more consistent result can be obtained by measuring the point at which the contrast between the black and white lines on the chart reduces to 50% of maximum, or MTF50 (as resolution decreases so too does contrast). So while MTF50 does not determine the ultimate resolution of the system, it gives a very reliable performance indicator that is repeatable and consistent from test to test. What it will tell you is how sharp one camera will appear to be compared to the next.
As Nyquist is half the pixel resolution of the system, for a 1920 sensor anything over 960 LP/ph will potentially aliase, so we don’t want resolution above this. You don’t want to see a higher number than this as it has the potential for problems as the extinction resolution must be higher than this and thus there must be the risk of aliasing. This where seeing the MTF curve helps, as it’s important to see how quickly the resolution is attenuated past MTF50.
With Bayer pattern sensors it’s even more problematic due to the reduced pixel count for the R and B samples compared to G.
The resolution of the EX1 and F3 is excellent for a 1080 camera, cameras that boast higher than 960 LP/ph will have aliasing issues, indeed the EX1/EX3 can aliase in some situations as does the F3. These cameras are right at the limits of what will allow for a good, sharp image at 1920×1080.
Post Reply