This is a question that comes up a lot. Especially from those migrating to a camera with a CineEI mode from a camera without one. It perhaps isn’t obvious why you would want to use a shooting mode that has no way of adding gain to the recordings.
If using the CineEI mode shooting S-log3 at the base ISO, with no offsets or anything else then there is very little difference between what you record in Custom mode at the base ISO and CineEI at the base EI.
But we have to think about what the CineEI mode is all about. It’s all about image quality. You would normally chose to shoot S-Log3 when you want to get the highest possible quality image and CineEI is all about quality.
The CineEI mode allows you to view via your footage via a LUT so that you can get an appreciation of how the footage will look after grading. Also when monitoring and exposing via the LUT because the dynamic range of the LUT is narrower, your exposure will be more accurate and consistent because bad exposure looks more obviously bad. This makes grading easier. One of the keys to easy grading is consistent footage, footage where the exposure is shifting or the colours changing (don’t use ATW with Log!!) can be very hard to grade.
Then once you are comfortable exposing via a LUT you can start to think about using EI offsets to make the LUT brighter or darker. When the LUT is darker you open the aperture or reduce the ND to return the LUT to a normal looking image and vice versa with a brighter LUT. This then changes the brightness of the S-log3 recordings and you use this offsetting process to shift the highlight/shadow range as well as noise levels to suit the types of scenes you are shooting. Using a low EI (which makes the LUT darker) plus correct LUT exposure (the darker LUT will make you open the aperture to compensate) will result in a brighter recording which will improve the shadow details and textures that are recorded and thus can be seen in the shadow areas. At the same time however that brighter exposure will reduce the highlight range by a similar amount to the increase in the shadow range. And no matter what the offset, you always record at the cameras full dynamic range.
I think what people misunderstand about CineEI is that it’s there to allow you to get the best possible, highly controlled images from the camera. Getting the best out of any camera requires appropriate and sufficient light levels. CineEI is not designed or intended to be a replacement for adding gain or shooting at high recording ISOs where the images will be already compromised by noise and lowered dynamic range.
CineEI exists so that when you have enough light to really make the camera perform well you can make those decisions over noise v highlights v shadows to get the absolute best “negative” with consistent and accurate exposure to take into post production. It is also the only possible way you can shoot when using raw as raw recordings are straight from the sensor and never have extra gain added in camera.
Getting that noise/shadow/highlight balance exactly right, along with good exposure is far more important than the use of external recorders or fatter codecs. You will only ever really benefit fully from higher quality codecs if what you are recording is as good as it can be to start with. The limits as to what you can do in post production are tied to image noise no matter what codec or recording format you use. So get that bit right and everything else gets much easier and the end result much better. And that’s what CineEI gives you great control over.
When using CineEI or S-Log3 in general you need to stop thinking “video camera – slap in a load if gain if its dark” and think “film camera – if its too dark I need more light”. The whole point of using log is to get the best possible image quality, not shooting with insufficient light and a load of gain and noise. It requires a different approach and completely different way of thinking, much more in line with the way someone shooting on film would work.
What surprises me is the eagerness to adopt shutter angles and ISO ratings for electronic video cameras because they sound cool but less desire to adopt a film style approach to exposure based on getting the very best from the sensor. In reality a video sensor is the equivalent of a single sensitivity film stock. When a camera has dual ISO then it is like having a camera that takes two different film stocks. Adding gain or raising the ISO away from the base sensitivity in custom mode is a big compromise that can never be undone. It adds noise and decreases the dynamic range. Sometimes it is necessary, but don’t confuse that necessity with getting the very best that you can from the camera.
For more information on CineEI see:
Using CineEI with the FX6
Can you tell which is genuine and which is fake? It would appear that a number of fake BP-U batteries are starting to show up on ebay and other less reputable places. The battery on the left won’t charge on a genuine Sony charger, this tells me it is not a real Sony battery.
With the new FX6 making use of SD cards to record higher bit rate codecs the number of gigabytes of SD card media that many user will will be getting through is going to be pretty high. The more gigabytes of memory that you use, the more the chance of coming across a duff memory cell somewhere on your media.
